Pressure Converter

Convert pressure between pascals, bar, psi, atmospheres and mercury-based units. Useful for tyres, weather, diving, engineering and laboratory work.

Conversions • Bar, psi & atm • Exact factors • Updated November 18, 2026 • Reviewed by the GlobalCalcly editorial team
Unit conversion Choose units and enter a value
From and to
Factors use exact international definitions, so results are not rounded by the converter.
Converted value
—

Enter a value to convert.

Conversion rate —
Reverse rate —
Category Pressure
Formula —

Pressure units in daily life

Pressure is force per unit area. The SI unit is the pascal, but different industries use different units: bar for tyres and weather in Europe, psi for tyres and plumbing in the US, and atmospheres for diving and science.

FromToValue
1 barpsi14.5038 psi
1 atmospherebar1.01325 bar
1 atmospherepsi14.6959 psi
1 psikilopascals6.89476 kPa
1 mmHgpascals133.322 Pa

Standard atmospheric pressure is 101,325 Pa, 1.01325 bar or 14.6959 psi. Weather reports often use hectopascals, where 1 hPa equals 100 Pa.

Absolute, gauge and differential pressure

Absolute pressure is measured against a perfect vacuum. Gauge pressure is measured against the surrounding atmosphere, so it reads zero at sea level. Tyre pressure and plumbing pressure are usually gauge pressures. Add atmospheric pressure to a gauge reading to get absolute pressure.

How to convert pressure

result = value × (factorfrom ÷ factorto)

For example, to convert 32 psi to bar:

32 × (6,894.757293168 ÷ 100,000) = 2.2063 bar

Worked examples

  • 2 bar to psi: 2 × 14.5038 = 29.01 psi.
  • 1 atm to kPa: 101.325 kPa.
  • 30 psi to bar: 30 × 0.0689476 = 2.068 bar.
  • 760 mmHg to atm: 760 × 133.322387415 ÷ 101,325 = 0.99997 atm.

For tyre pressure, a common car recommendation is 32–36 psi, which is about 2.2–2.5 bar. Always use the vehicle manufacturer's specification rather than a generic figure.

Common mistakes to avoid

  • Adding an atmosphere twice. A tyre gauge reading 35 psi is already gauge pressure. Its absolute pressure is 35 + 14.6959 = 49.70 psi. Substituting 1 bar for 1 atm adds 14.5038 instead of 14.6959, a 0.19 psi error.
  • Reading psig as psia. A gauge marked psig reads zero in open air, while an absolute sensor marked psia reads about 14.7 psi at sea level. Comparing the two without correction is a 14.7 psi mistake.
  • Using a hot tyre reading as the specification. Pressure rises roughly 1 psi per 10 °F (about 1.8 psi per 10 °C) as a tyre warms, so set pressures cold.
  • Assuming sea-level atmosphere at altitude. At 2,000 m the atmosphere is near 79.5 kPa, so the same gauge reading corresponds to a lower absolute pressure.

What changes the number most

Whether the figure is gauge or absolute matters more than the unit. At low pressures the atmospheric offset is large relative to the reading: 5 psi gauge is 19.70 psi absolute, nearly four times the gauge value. At 3,000 psi the offset is under 0.5% and is often dropped.

Temperature and altitude change the physical pressure a fixed amount of gas exerts, but they never change how units convert. If a reading is taken hot or high up and compared with a sea-level specification, correct the measurement first and convert afterwards.

How to check the result

Convert to pascals, the shared base, and back. 45 psi is 45 × 6,894.757 = 310,264 Pa, or 3.1026 bar; 3.1026 × 100,000 ÷ 6,894.757 returns 45.00 psi. Useful anchors: 1 atm is 101.325 kPa, 1 bar is 100 kPa and 1 psi is 6.895 kPa. A weather reading near 1,013 hPa should convert to roughly 1 atm.

A vacuum gauge is the mirror case: a reading of −0.6 bar gauge is 0.413 bar absolute, because 1.01325 − 0.6 = 0.41325. The minus sign does not survive the shift to absolute pressure.

When to use this calculator

Pressure appears on gauges, weather charts and equipment plates, each with its own preferred unit. These four cases cover most household and workshop needs.

  • Bicycle tyres. A road tyre at 90 psi is 6.21 bar, and a 100 psi track tyre is 6.89 bar. A floor pump marked only in bar needs the bar figure, not a rough doubling.
  • Boilers and plumbing. A sealed heating system often runs at 1.5 bar, which is 21.76 psi or 150 kPa.
  • Air tools. A workshop compressor set to 8 bar delivers 116 psi; a spray gun may ask for 30 psi, or 2.07 bar.
  • Diving. A cylinder filled to 200 bar holds the same pressure as 2,900.8 psi. Depth gauges and dive computers may use either.

When a specification gives a range, convert both ends and keep the order: 100–120 bar is 1,450–1,740 psi, not 1,740–1,450. Converting the midpoint instead gives a single figure that can fall outside the stated tolerance.

A gauge's scale decides how precisely you can set a pressure. A 0–60 psi gauge with 2 psi markings cannot resolve 32 psi better than about ±1 psi, while a digital gauge reading to 0.1 psi can. Convert the target first, then check that the instrument can actually show the difference you are trying to set. For a tyre, 2.2 and 2.4 bar are about 3 psi apart, so aim for the middle of the recommended range rather than an edge.

Frequently asked questions

How many psi are in 1 bar?

One bar equals 14.5038 psi, so a 2-bar tyre reading is about 29 psi. Multiply bar by 14.5038 for psi, or divide psi by the same figure to return to bar. Most petrol station air pumps in Europe mark bar only.

What is standard atmospheric pressure?

Standard atmospheric pressure is 101,325 pascals, which is 1.01325 bar, 14.6959 psi or 760 millimetres of mercury. It is defined at sea level, 15 °C and average gravity, so real weather shifts it slightly. Aircraft altimeters are calibrated against this reference.

Is psi the same as bar?

No. One psi equals about 0.06895 bar, so a bar is roughly 14.5 times larger. Tyre gauges in the US read psi, while European and Asian specifications commonly use bar or kilopascals. Kilopascals also appear on many European tyre placards.

What is the difference between gauge and absolute pressure?

Gauge pressure reads zero at sea level because it ignores the atmosphere. Absolute pressure includes it, so a gauge reading of 2 bar is about 3 bar absolute. Vacuum work and chemistry usually need absolute values.

Why do weather reports use hectopascals?

Hectopascals keep weather numbers compact, with standard pressure at 1,013.25 hPa. One hectopascal equals one millibar, so older charts convert without any arithmetic, and forecasts keep the familiar three-digit style. Forecast charts print four digits, such as 1,013, without a decimal point.

Sources & methodology

Results are estimates for general information. For medical, legal or financial decisions, confirm with a qualified professional.