Length Converter
Convert length and distance between metric and imperial units. Type a value, choose the units, and the result updates instantly using exact international definitions.
Enter a value to convert.
Common length conversions
Length is one of the easiest quantities to convert because most modern units are defined against the metre. The inch, foot, yard and mile all have exact legal definitions, so there is no rounding error in the conversion factor itself.
| From | To | Exact value |
|---|---|---|
| 1 inch | centimeters | 2.54 cm |
| 1 foot | centimeters | 30.48 cm |
| 1 yard | meters | 0.9144 m |
| 1 mile | kilometers | 1.609344 km |
| 1 nautical mile | kilometers | 1.852 km |
A nautical mile is not the same as a land mile. It is based on one minute of latitude and is used in aviation and marine navigation.
Metric and imperial systems
The metric system uses powers of ten: 10 millimeters make a centimeter, 100 centimeters make a meter and 1,000 meters make a kilometer. Imperial units do not share a single base: 12 inches make a foot, 3 feet make a yard and 5,280 feet make a mile.
How to convert length
Each unit is expressed as a multiple of the metre. To convert, multiply by the from-factor and divide by the to-factor:
For example, to convert 5 miles to kilometers:
Worked examples
- 180 cm to feet: 180 × (0.01 ÷ 0.3048) = 5.9055 ft, or about 5 ft 10.9 in.
- 26.2 miles to kilometers: 26.2 × 1.609344 = 42.16 km, a marathon distance.
- 100 yards to meters: 100 × 0.9144 = 91.44 m.
When a result is very small or very large, the converter shows enough decimal places to keep the significant digits meaningful.
Common mistakes to avoid
- Treating feet and inches as a decimal. 5 ft 10 in is 70 in, or 5.833 ft, never 5.10 ft. Entered as 5.1 ft it converts to 5.1 x 30.48 = 155.45 cm instead of 177.8 cm, an error of about 22 cm.
- Using 2.5 cm per inch. The factor is exactly 2.54, so a 40-inch measurement is 100 cm by the shortcut and 101.6 cm in reality.
- Applying a linear factor to an area. A factor of 3.28 converts metres to feet, but square metres need 3.28 squared, or 10.76, per unit.
How to check the result
Convert back with the reciprocal and see whether the original number returns. A marathon of 26.2 miles becomes 42.16 km, and 42.16 / 1.609344 = 26.2. Check the order of magnitude against an anchor you already know: a metre is slightly longer than a yard, so a 100 m sprint is about 109 yards, and a kilometre is roughly 0.62 miles, so 10 km is about 6.2 miles. A result within a few percent of that estimate is almost certainly correct, while a factor-of-ten gap points to a misread prefix such as millimetres entered as centimetres.
What changes the number most
The conversion factors are fixed by definition, so nothing in the arithmetic alters the answer; only the pair of units does. The biggest jumps come from prefixes and from crossing systems: one metre is 1,000 millimetres, while one mile is 63,360 inches. Within imperial units the steps are irregular at 12, 3 and 5,280, so a wrong step rarely looks wrong by a familiar power of ten. The precision you keep matters at the margins: rounding 8.04672 km to 8.05 km drops 3.28 m, which no road sign needs but a survey does. Navigation adds a third mile: one nautical mile is exactly 1,852 m, so a 100 nautical mile leg covers 185.2 km, about 15% further than 100 land miles.
When to use this calculator
Length conversion shows up in three everyday situations: filling in a form that expects a different unit, buying material sold in one system while measuring in another, and checking whether a quoted dimension is plausible.
- Forms and official records. A height of 1.83 m is 6 ft 0 in, because 1.83 ÷ 0.3048 = 6.004 ft. Passport and visa forms usually want whole centimetres or feet and inches, not a decimal of a foot.
- Buying materials. Timber, pipe and fabric are often sold in one system and cut to measurements taken in the other. Convert the cut list once, then add the waste allowance in the unit you are ordering.
- Checking a spec. A 2.4 m ceiling is 7.87 ft, and a 30 cm tile is 11.81 in. If a listing claims a 10 ft ceiling for a flat with 2.4 m plans, the two descriptions disagree.
Match precision to the job. A room measured to the nearest centimetre is about 0.4 in, which is finer than any furniture fit needs; a machine part may need millimetres. Do not convert a rounded figure twice: convert the original measurement, then round the output.
Choose the unit the other person will use rather than the one you measured in. A vet, a tailor and a removal firm each expect a different scale, and the converter changes only the label, not the length. Write the unit beside every number in a mixed list, because a bare 72 could be inches or centimetres and the two differ by a factor of 2.54.
Frequently asked questions
How many feet are in a meter?
A meter equals 3.280839895 feet, so multiplying meters by that factor gives feet. To reverse it, divide the feet figure by the same number. For example, 1.8 meters converts to roughly 5.91 feet. The tool works in both directions as you type.
Is a nautical mile longer than a mile?
Yes, by about 15 percent. A nautical mile is defined as exactly 1,852 meters, while the international land mile is 1,609.344 meters. That 243-meter gap is why aviation and marine charts use nautical miles for distance. Sailors call one nautical mile per hour a knot.
Why is an inch exactly 2.54 cm?
Because the 1959 international yard and pound agreement set one inch at exactly 25.4 millimeters, which is 2.54 centimeters. Before that, different countries used slightly different inch standards, so the treaty created one shared definition for trade and engineering.
How do I convert centimeters to inches?
Divide the centimeter value by 2.54, since one inch is exactly 2.54 centimeters. A 30-centimeter measurement therefore equals 11.81 inches. Enter the number in the centimeter field and the inch result appears without pressing a button.
Does the converter use US or UK units?
This length tool gives the same answer either way, because feet, inches, yards and miles share identical definitions in both systems. The two systems only diverge in volume and weight, where US and imperial gallons differ by about 20 percent.
Sources & methodology
- National Institute of Standards and Technology — SI conversion factors.
- International Bureau of Weights and Measures (BIPM) — SI brochure.
- Calculation method: exact international length definitions, value × (from factor ÷ to factor).
Results are estimates for general information. For medical, legal or financial decisions, confirm with a qualified professional.