Body Fat Calculator

Estimate body fat from a few tape measurements. The calculator uses the U.S. Navy circumference method and also reports estimated fat mass and lean mass.

Health & Fitness • Tape measurements • Fat and lean mass • Updated November 18, 2026 • Reviewed by the GlobalCalcly editorial team
Measurements Measure relaxed, without pulling the tape tight
kg
cm
cm
cm
cm
Estimated body fat
—

Enter your measurements to estimate body fat.

Estimated fat mass (kg) —
Estimated lean mass (kg) —
Waist ÷ height —
Reference band —

Why circumference measurements are used

Laboratory methods such as DEXA and hydrostatic weighing are accurate but expensive. Tape measurements offer a practical estimate: the U.S. Navy method combines neck, waist, hip and height to approximate body fat without special equipment.

The formula is a statistical model, not a direct measurement. It tends to be reasonably close for people with typical proportions and less accurate for very muscular or very lean bodies. Use the trend over time rather than treating a single result as exact.

How to measure

  • Neck: below the larynx, with the tape sloping slightly downward at the front.
  • Waist: at the navel for men, at the narrowest point for women.
  • Hip: at the widest point of the buttocks, feet together.
  • Height: without shoes, standing straight.

Measure in the morning, before eating, and keep the tape snug but not compressed. Take each measurement twice and use the average. Consistency matters more than a perfect single reading.

The formulas

Men: %BF = 495 ÷ (1.0324 − 0.19077 × log10(waist − neck) + 0.15456 × log10(height)) − 450
Women: %BF = 495 ÷ (1.29579 − 0.35004 × log10(waist + hip − neck) + 0.22100 × log10(height)) − 450

All measurements are in centimetres in the metric version. The logarithms make the relationship non-linear, which is why small changes near the waist can move the estimate more than changes elsewhere.

Reading the result

Body fat percentage is only one signal of health. Waist-to-height ratio, blood pressure, fitness and medical history all matter. The reference bands shown are broad population ranges, not personal medical targets.

Tracking change

Measure under the same conditions each time. A change of one or two percentage points can fall within measurement error, so look for a consistent direction over several weeks. Pair the estimate with waist measurements, photos and performance in training.

Limitations of the Navy method

The formula was developed on specific populations and assumes a typical fat distribution. It can overestimate body fat in trained athletes with thick necks and underestimate it in people with central fat but slim limbs. Age is not part of the basic formula, even though body composition changes with age.

If the result matters for a medical decision, use a clinical method and speak to a professional. This calculator is an educational estimate.

Fat mass and lean mass

Once a percentage is estimated, fat mass is weight × percentage and lean mass is the remainder. Lean mass includes muscle, bone, organs and water, not just muscle. A change in lean mass can reflect hydration as much as muscle gain.

What to do with the number

Use it to set a realistic direction: maintain, reduce slowly or build. Very low body fat can impair hormones, immunity and performance, so lower is not automatically better. Sustainable changes in food and training matter more than chasing a single figure.

How to check the result

Run one set of numbers through the male formula by hand: 175 cm tall, 38 cm neck, 85 cm waist, 75 kg. Waist minus neck is 47, and the base-ten logarithm of that is 1.672; the logarithm of the height is 2.243. The bracket becomes 1.0324 minus 0.19077 times 1.672 plus 0.15456 times 2.243, which is 1.0601, and 495 divided by 1.0601 minus 450 is about 16.9 percent. That is 12.7 kg of fat mass and 62.3 kg of lean mass, which add back to 75 kg.

Then look at the waist-to-height output: 85 divided by 175 is about 0.49. A ratio at or above 0.50 is widely used as a flag for central fat, so 0.49 alongside 16.9 percent is internally consistent. If the two checks disagree sharply, remeasure before drawing any conclusion from either.

What changes the number most

Because the circumference terms sit inside a logarithm, waist and neck move the estimate far more than weight does; weight only converts the percentage into kilograms. Two centimetres on the waist takes this example from 16.9 to about 18.5 percent, while two centimetres on the neck pulls it down to roughly 15.4. A three-kilogram change on the scale with the tape unchanged leaves the percentage untouched and shifts fat mass by about half a kilogram.

Height has a smaller effect, and sex changes the whole equation: the female version uses a different constant and adds hip circumference, so male and female results cannot be compared point for point.

Common mistakes to avoid

A stretched fabric tape reads long and biases every result in the same direction, so check it against a rigid ruler once. Measure before training and before a large meal rather than after either, because a pumped arm or a full abdomen changes the reading without changing fat. Entering a hip measurement for a man has no effect on the result, while entering pounds as kilograms inflates fat mass and leaves the percentage untouched.

Frequently asked questions

How accurate is the Navy body fat formula?

For people with average proportions it typically lands within three to four percentage points of a DEXA scan. Accuracy drops for very lean athletes, older adults and anyone with a large waist, where the circumference model overestimates or underestimates fat.

Do I need the hip measurement if I am male?

No, the male equation uses neck, waist and height only, so leave the hip field empty. The hip circumference appears solely in the female formula, where it is measured at the widest point of the buttocks alongside the neck and waist.

Where exactly should I measure my waist?

Men measure horizontally at the navel; women measure at the narrowest point of the torso, usually just above the navel. Keep the tape snug but not compressing skin, breathe out normally, and take two readings to average out small placement errors.

Why does my result differ from my smart scale?

Scales estimate fat with bioelectrical impedance, which shifts with hydration, recent meals, exercise and even room temperature. Tape measurements use a different model entirely. A three to five point gap is normal, so track one method over months instead of comparing the two.

What is a healthy body fat percentage?

Common reference bands are roughly 8 to 20 percent for men and 21 to 33 percent for women, with athletes lower and older adults higher. These ranges describe populations, not individuals, and waist size, fitness and blood markers matter as much as the percentage.

Sources & methodology

  • U.S. Navy — circumference-based body fat estimation method.
  • American Council on Exercise — body composition reference ranges.
  • Calculation method: U.S. Navy circumference equations, metric measurements.

General information only — not medical advice, diagnosis or treatment. Talk to a qualified healthcare professional about your situation.